Chemistry Solutions Calculator
Solution chemistry comes down to a handful of relationships between moles, mass, volume and concentration. In the lab you need them to make up a solution; in an exam you need them to rearrange in either direction without slipping on units.
This calculator brings the six most used ones together: molarity, molality, normality, mole fraction, dilution and pH. Choose one, enter the quantities you have, leave the unknown empty, and it works out the missing value with its unit and a worked example to compare against.
Four ways to state a concentration
- Molarity (M) is moles of solute per litre of solution. The calculator takes the solute's mass and molar mass, so you skip the separate moles step: M = (mass ÷ molar mass) ÷ volume in litres.
- Molality (m) is moles of solute per kilogram of solvent. Because it uses mass rather than volume, it does not change with temperature, which is why it appears in boiling and freezing point problems.
- Normality (N) is molarity times the n-factor: the number of H⁺ or OH⁻ ions, or electrons, each formula unit supplies. 1 M H₂SO₄ is 2 N.
- Mole fraction (x) is the share of all the moles that belong to one component; the fractions of every component add up to 1.
Dilution: M₁V₁ = M₂V₂
Adding solvent changes the volume but not the amount of solute, so concentration times volume stays the same before and after. To make a working solution from a stock, enter the stock concentration, the target concentration and the final volume, and leave V₁ empty: the answer is how much stock to measure out. Both volumes only need to be in the same unit, so millilitres are fine.
pH, [H⁺] and pOH
pH is −log₁₀ of the hydrogen ion concentration in mol/L, and at 25 °C pH + pOH = 14. Enter any one of the three and the calculator gives the other two. A change of one pH unit means a tenfold change in [H⁺]: a solution at pH 3 has ten times the hydrogen ions of one at pH 4. Below 7 is acidic, 7 is neutral and above 7 is basic, at 25 °C.
How to use this tool
- Choose the calculation: Molarity, molality, normality, mole fraction, dilution or pH.
- Enter the values you have: Mass in grams, molar mass in g/mol, volume in litres unless labelled mL.
- Leave the unknown empty: For pH, fill in just one of pH, [H⁺] or pOH.
- Check the worked example: Each calculation shows a typical example below the answer.
Features
- Six calculations in one place
- Solves for whichever value is missing
- Molarity straight from grams and molar mass
- pH, [H⁺] and pOH from any one of them
- Worked example for each calculation
Worked examples
Salt solution
5.85 g of NaCl (molar mass 58.44 g/mol) made up to 500 mL.
5.85 ÷ 58.44 = 0.1001 mol; 0.1001 ÷ 0.5 L
Result: About 0.200 M.
Diluting a stock acid
500 mL of 0.1 M needed from a 2 M stock.
V₁ = 0.1 × 500 ÷ 2
Result: Measure 25 mL of stock and make it up to 500 mL.
Glucose in water
18 g of glucose (180 g/mol) in 250 g of water.
18 ÷ 180 = 0.1 mol; 0.1 ÷ 0.25 kg
Result: 0.4 mol/kg.
pH from concentration
A solution with [H⁺] = 0.001 mol/L.
pH = −log₁₀(0.001); pOH = 14 − 3
Result: pH 3, pOH 11: acidic.
Who it is for
- Class 11 and 12 chemistry: Check numericals from the Solutions and Equilibrium chapters.
- Lab preparation: Work out how much stock to dilute for a practical.
- Pharmacy and biology students: Prepare buffers and reagents at the right strength.
Tips
- Convert millilitres to litres for molarity: divide by 1,000.
- For dilution, add acid to water, never water to concentrated acid.
- Look up molar masses from the periodic table to at least two decimal places for accurate results.
Frequently asked questions
What happened to the separate molarity and pH calculators?
They are part of this calculator now. The old addresses still work and open it with the same calculation selected.
What is the difference between molarity and molality?
Molarity divides moles by litres of solution; molality divides by kilograms of solvent. Molarity changes slightly with temperature because volume does; molality does not.
How do I find the n-factor for normality?
For an acid it is the number of replaceable H⁺ ions (2 for H₂SO₄), for a base the number of OH⁻ ions (2 for Ca(OH)₂), and for a redox reagent the electrons gained or lost per formula unit (5 for KMnO₄ in acid).
Is pH + pOH always 14?
Only at 25 °C. The sum depends on the ionisation of water, which changes with temperature; at body temperature it is about 13.6.